need a unique h22 basemap

Calibrations for S-Manager - Use all calibrations at your own risk (dyno tuning recommended)
Post Reply
Slipknotko
Posts: 2
Joined: Wed Mar 21, 2018 6:43 pm

need a unique h22 basemap

Post by Slipknotko » Thu Mar 22, 2018 11:08 pm

so I have tried all the h22 basemaps on the forums the car starts then dies right away.
id 1000cc injectors
stock map sensor for now
wastegates set to 8 psi springs.
i just installed a rywire tucked harness with conversion built in for the new obd1 hondata ecu brand new from rywire.
tach and fuel pump i wired in as well as the wideband o2 sensor is wired into d14.
i live in alberta which i think is 14psi atmospheric pressure.
i also am not running an iac valve and have the throttle body opened a little to allow air in it ran on the link ecu prior to the wireing harness and ecu change . i just need it to run so i can get it to the dyno shop.
fuel pump is cycling fine.
i get an error o2 heater and iac i disabled iac and o2 no change .

i hope you guys can help

Slipknotko
Posts: 2
Joined: Wed Mar 21, 2018 6:43 pm

Re: need a unique h22 basemap

Post by Slipknotko » Sun Mar 25, 2018 4:42 pm

so I was able to keep it running to do some datalogging . still runs like garbage hope this will let you guys help cause my car is stuck in my underground parking garage till I get it running well enough to the dyno shop 40km away
Attachments
h22.s3d
(1.06 MiB) Downloaded 63 times
h222.s3d
(2.51 MiB) Downloaded 44 times
h2222.s3d
(501.11 KiB) Downloaded 47 times

G. Wiffington
Posts: 33
Joined: Tue Nov 21, 2017 12:24 pm

Re: need a unique h22 basemap

Post by G. Wiffington » Tue May 08, 2018 10:29 am

I have a decent H22 Map for a Euro-R setup (11:1 CR)

What is you AFR upon starting? I would bet it is way too rich, as all the H22 maps seem to be. Pull some fuel from the whole map & see if it helps out.

r1z1nginfern0
Posts: 1
Joined: Sun Aug 11, 2019 8:16 pm

Re: need a unique h22 basemap

Post by r1z1nginfern0 » Sun Aug 11, 2019 8:53 pm

G. Wiffington, I have been struggling to get my euro r to idle and not cut after throttle input then letting off. If you have a stock map could I possibly get it? I would greatly appreciate it seeing how the tuner I'm trying to get to is 300 miles away...

99 GSR
01 Euro R H22A (stock PDE IM, injectors, and internals)
2 wire iacv
Egr delete
1320 H2B Header

InterAV
Posts: 2
Joined: Sat Jul 13, 2019 8:06 pm

Re: need a unique h22 basemap

Post by InterAV » Sun Aug 25, 2019 1:54 pm

r1z1nginfern0 wrote:
Sun Aug 11, 2019 8:53 pm
G. Wiffington, I have been struggling to get my euro r to idle and not cut after throttle input then letting off. If you have a stock map could I possibly get it? I would greatly appreciate it seeing how the tuner I'm trying to get to is 300 miles away...

99 GSR
01 Euro R H22A (stock PDE IM, injectors, and internals)
2 wire iacv
Egr delete
1320 H2B Header
Did you ever manage to find a good basemap? I have pretty much the same setup as you.

Post Reply