Urg.. Flashpro goes crazy..
Urg.. Flashpro goes crazy..
Just tried flashpro,
register and lock the flashpro to the ecu
flash a base map..
after flashing..... damn... my car can't start, flash manager show ecu with a cross...
tried to upload again... still won't work..
tried to unlock, flashpro say vin not recognised...!!!!!
Arghhhh..
HONDATA... Help!!!!
register and lock the flashpro to the ecu
flash a base map..
after flashing..... damn... my car can't start, flash manager show ecu with a cross...
tried to upload again... still won't work..
tried to unlock, flashpro say vin not recognised...!!!!!
Arghhhh..
HONDATA... Help!!!!
For a start you will need to tell us:
- what vehicle you have
- what ECU you are using
- what calibration you have loaded
- if the ECU has been reflashed before
Unplug the FlashPro from the vehicle, switch the ignition off for at least 1 minute, plug the FlashPro back into the vehicle, connect to the laptop, switch on the ignition, then tell us what the icons are at the bottom left of the screen.
- what vehicle you have
- what ECU you are using
- what calibration you have loaded
- if the ECU has been reflashed before
Unplug the FlashPro from the vehicle, switch the ignition off for at least 1 minute, plug the FlashPro back into the vehicle, connect to the laptop, switch on the ignition, then tell us what the icons are at the bottom left of the screen.
Hondata
register user details
register flash pro with hondata
open new calibration stock fd2r map
upload new calibration.. so far so good
upload stage 1 done, stage 2 done.... car can't start...
flashpro manager show ecu with a cross..
can't unlock, can't unregister.. but can flash... software only show stage 1
37820-RRC-.. need to check the last number.
just check my ecu.. the memory is wiped clean... no program at all...jeez..
register flash pro with hondata
open new calibration stock fd2r map
upload new calibration.. so far so good
upload stage 1 done, stage 2 done.... car can't start...
flashpro manager show ecu with a cross..
can't unlock, can't unregister.. but can flash... software only show stage 1
37820-RRC-.. need to check the last number.
just check my ecu.. the memory is wiped clean... no program at all...jeez..
Hmmm... I did mine with FlashPro.. and it works fine.skyliner wrote:register user details
register flash pro with hondata
open new calibration stock fd2r map
upload new calibration.. so far so good
upload stage 1 done, stage 2 done.... car can't start...
flashpro manager show ecu with a cross..
can't unlock, can't unregister.. but can flash... software only show stage 1
37820-RRC-.. need to check the last number.
just check my ecu.. the memory is wiped clean... no program at all...jeez..
Car can start and also run perfectly without a glitch.
try unlocking the FlashPro by reverting to stock map... then start the car. If car can start then u must have made a mistake while uploading the map to ECU.
Note: you must make sure ur ignition is at ON during the process.
Hello hondata,
I think I have this same problem today.
I install the new version 1.1.4.4; reflash my car to stock and drove for 20 minutes, then I want to upload a new calibration, during the process I receive a warning, since then my ECU is blocked.
I cant upload any calibration and the car doesnt start.
I attach the screen information, and send the information to hondata support.
My car is a 2008 Latinoamerican SI, K01, and the ECU has been reflashed before.
Please help
I think I have this same problem today.
I install the new version 1.1.4.4; reflash my car to stock and drove for 20 minutes, then I want to upload a new calibration, during the process I receive a warning, since then my ECU is blocked.
I cant upload any calibration and the car doesnt start.
I attach the screen information, and send the information to hondata support.
My car is a 2008 Latinoamerican SI, K01, and the ECU has been reflashed before.
Please help
- Attachments
-
- 1.jpg (70.27 KiB) Viewed 6542 times
Please read the following: http://www.hondata.com/help/flashpro/ec ... b=recovery