P2185 after wideband connection to pin A33

FlashPro questions & answers specific to the FD2 Japanese Civic Type R
Post Reply
jlhk
Posts: 6
Joined: Sun May 31, 2015 3:29 am

P2185 after wideband connection to pin A33

Post by jlhk »

Dear experts, I am new to Honda and Hondata, I have recently purchased a FD2 (Japanese Type R) and a Flashpro. To maximize my tuning accuracy, I have installed a wideband (AEM with meter and control unit) according to the instruction from flashpro help. I have tried all ECU pin and found that only the A33 pin (secondary ECT sensor) worked. The wideband is functioning well and I am getting a reading similar to stock primary O2 sensor, however, the CEL lights up and the code was P2185 (secondary ECT sensor high voltage), could someone help me with this issue? I could not turn off the error code by Flashpro. Thanks in advance.

User avatar
Hondata
Site Admin
Posts: 9339
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: P2185 after wideband connection to pin A33

Post by Hondata »

What calibration are you using?
Hondata

jlhk
Posts: 6
Joined: Sun May 31, 2015 3:29 am

Re: P2185 after wideband connection to pin A33

Post by jlhk »

Hondata r reflash

User avatar
Spunkster
Site Admin
Posts: 18948
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: P2185 after wideband connection to pin A33

Post by Spunkster »

Can you post the calibration that you have uploaded to the ECU.

User avatar
Hondata
Site Admin
Posts: 9339
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: P2185 after wideband connection to pin A33

Post by Hondata »

You cannot disable the secondary ECT sensor with that calibration type. I would switch to a race calibration for that vehicle.
Hondata

jlhk
Posts: 6
Joined: Sun May 31, 2015 3:29 am

Re: P2185 after wideband connection to pin A33

Post by jlhk »

May i know how do i flash a race type calibration into my ecu please?

jlhk
Posts: 6
Joined: Sun May 31, 2015 3:29 am

Re: P2185 after wideband connection to pin A33

Post by jlhk »

My calibration attached.

I think I need a way to turn off the DTC code. I used other ecu softwares in the past and some are able to turn off the DTC code selectively, can my flashpro do that?

Thanks in advance.
Attachments
FD2150805.fpcal
(11.34 KiB) Downloaded 148 times

jlhk
Posts: 6
Joined: Sun May 31, 2015 3:29 am

Re: P2185 after wideband connection to pin A33

Post by jlhk »

Oic, thanks, i will try, sorry newbie learn slow

jlhk
Posts: 6
Joined: Sun May 31, 2015 3:29 am

Re: P2185 after wideband connection to pin A33

Post by jlhk »

Dear Admins,

Converted to race calibration, problem solved, thank you very much.

User avatar
Hondata
Site Admin
Posts: 9339
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: P2185 after wideband connection to pin A33

Post by Hondata »

Thanks for the feedback.
Hondata

Post Reply