Engine start logging not possible anymore?
Engine start logging not possible anymore?
Hi hondata,
I found out with the latest version the engine start can not logged anymore. The logs are still available but can not be saved on the PC...
I can record logs only if the engine is still running.
Installed flash pro manager: 2.3.5
I found out with the latest version the engine start can not logged anymore. The logs are still available but can not be saved on the PC...
I can record logs only if the engine is still running.
Installed flash pro manager: 2.3.5
Re: Engine start logging not possible anymore?
Does your car have push button start?
Re: Engine start logging not possible anymore?
Yes, its a FN2!Spunkster wrote:Does your car have push button start?
But erlier it worked!
2008 Honda Civic TypeR FN2
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Re: Engine start logging not possible anymore?
Any news about this?
2008 Honda Civic TypeR FN2
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Re: Engine start logging not possible anymore?
Can you tell us exactly step by step what you are doing?
Re: Engine start logging not possible anymore?
Here the detailing of my problem recently:
Datalog-Session #1:
1. Plug Flashpro into OBD2-Port
2. Switch key to ignition-position
3. Press Datalog-Button (before start the engine) to start a Datalog (Datalog LED lights up/flashes)
4. Now start the engine
5. The Datalog LED goes out/canceled (i think no datalog is saved on the Flashpro!)
6. It is not possible anymore to make Datalogs from the engine cranking/starting (in earlier versions, this was no problem!)
If i press the Datalog-Button after cranking/engine start, then i can make datalogs still without any problems (datalogs on the Flashpro in the datalog-list)
-> Now i make more datalogs after this engine start session are saved on the Flashpro (download/save from Flashpro to notebook and open from/with Flashpro-Manager are possible!)
#1 Drive session completed -> stop engine!
---
After ~8 hours i make a new session (Flashpro permanently connected to the OBD2-Port over the time between Session #1 to Session #2!)
Datalog-Session #2 (The previous datalogs are still exist on the FlashPro):
1. Flashpro is still pluged into OBD2-Port
2. Switch key to ignition-position
3. Press Datalog-Button (before start the engine) to start a Datalog (Datalog LED lights up/flashes)
4. Now start the engine
5. The Datalog LED goes out/canceled (i think no datalog is saved on the Flashpro!)
6. It is not possible anymore to make Datalogs from the engine cranking/starting (in earlier versions, this was no problem!)
If i press the Datalog-Button after cranking/engine start, then i can make datalogs still without any problems!
-> Now i make more datalogs after this engine start session are saved on the Flashpro.
The first 1-2 logs in this session are correct (download/save from Flashpro to notebook are possible, storages are on my notebook!)
Then i make more 1-4 logs are recorded from the Flashpro, (download/save from Flashpro to notebook are possible, but no storages on my notebook!)
The downloaded files do not exist on my notebook!
Neither, even if I try several times to save the files!
Accordingly i can not open the files from/with Flashpro-Manager!
---
#1: Furthermore something is at FlashPro already over years:
If i upload a Map from the secondary storage from the Flashpro, the Flashpro always make a short datalog or save a short datalog to the Flashpro.
I think this which, because I have to press the "datalog-button" to upload a Map from secondary storage of the Flashpro!?
This problem/phenomenon I do not have, if I a upload a primary Map to the ECU or if i upload Maps (primary/secondary) with my notebook to the ECU, because I do not press the "datalog-button" in this case!
#2: And an onother bug in Flashpro-Manager:
If i open a read-only Flashpro-Map over the Windows-Explorer to open in the Flashpro-Manager and would save this file in FlashPro Manager, the program (FlashPro-Manager) crashes.
IF I would like to open the file directly in FlashPro-Manager, the message "read only" pops up!
I hope you understand and can fix this issues?
Thanks alot!
Datalog-Session #1:
1. Plug Flashpro into OBD2-Port
2. Switch key to ignition-position
3. Press Datalog-Button (before start the engine) to start a Datalog (Datalog LED lights up/flashes)
4. Now start the engine
5. The Datalog LED goes out/canceled (i think no datalog is saved on the Flashpro!)
6. It is not possible anymore to make Datalogs from the engine cranking/starting (in earlier versions, this was no problem!)
If i press the Datalog-Button after cranking/engine start, then i can make datalogs still without any problems (datalogs on the Flashpro in the datalog-list)
-> Now i make more datalogs after this engine start session are saved on the Flashpro (download/save from Flashpro to notebook and open from/with Flashpro-Manager are possible!)
#1 Drive session completed -> stop engine!
---
After ~8 hours i make a new session (Flashpro permanently connected to the OBD2-Port over the time between Session #1 to Session #2!)
Datalog-Session #2 (The previous datalogs are still exist on the FlashPro):
1. Flashpro is still pluged into OBD2-Port
2. Switch key to ignition-position
3. Press Datalog-Button (before start the engine) to start a Datalog (Datalog LED lights up/flashes)
4. Now start the engine
5. The Datalog LED goes out/canceled (i think no datalog is saved on the Flashpro!)
6. It is not possible anymore to make Datalogs from the engine cranking/starting (in earlier versions, this was no problem!)
If i press the Datalog-Button after cranking/engine start, then i can make datalogs still without any problems!
-> Now i make more datalogs after this engine start session are saved on the Flashpro.
The first 1-2 logs in this session are correct (download/save from Flashpro to notebook are possible, storages are on my notebook!)
Then i make more 1-4 logs are recorded from the Flashpro, (download/save from Flashpro to notebook are possible, but no storages on my notebook!)
The downloaded files do not exist on my notebook!
Neither, even if I try several times to save the files!
Accordingly i can not open the files from/with Flashpro-Manager!
---
#1: Furthermore something is at FlashPro already over years:
If i upload a Map from the secondary storage from the Flashpro, the Flashpro always make a short datalog or save a short datalog to the Flashpro.
I think this which, because I have to press the "datalog-button" to upload a Map from secondary storage of the Flashpro!?
This problem/phenomenon I do not have, if I a upload a primary Map to the ECU or if i upload Maps (primary/secondary) with my notebook to the ECU, because I do not press the "datalog-button" in this case!
#2: And an onother bug in Flashpro-Manager:
If i open a read-only Flashpro-Map over the Windows-Explorer to open in the Flashpro-Manager and would save this file in FlashPro Manager, the program (FlashPro-Manager) crashes.
IF I would like to open the file directly in FlashPro-Manager, the message "read only" pops up!
I hope you understand and can fix this issues?
Thanks alot!
Last edited by R-12914 on Sat Mar 19, 2016 1:00 am, edited 6 times in total.
2008 Honda Civic TypeR FN2
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Re: Engine start logging not possible anymore?
I can sign this steps.
I can also say it is winter and the battery is a little bit under stress. So in few mornings I get the information from the flash pro manager - battery warning 11.7 volt. (under 12 volt)
My battery is 1 year old and the engine start pretty good under this conditions. So Maybe the flashpro must also plugged in the notebook to make the engine start log?
I can also say it is winter and the battery is a little bit under stress. So in few mornings I get the information from the flash pro manager - battery warning 11.7 volt. (under 12 volt)
My battery is 1 year old and the engine start pretty good under this conditions. So Maybe the flashpro must also plugged in the notebook to make the engine start log?
Re: Engine start logging not possible anymore?
I do not think, that this trouble comes from there!typer86 wrote:I can sign this steps.
I can also say it is winter and the battery is a little bit under stress. So in few mornings I get the information from the flash pro manager - battery warning 11.7 volt. (under 12 volt)
My battery is 1 year old and the engine start pretty good under this conditions. So Maybe the flashpro must also plugged in the notebook to make the engine start log?
On the one hand, because I never had that problem in erlier times.
and
on the other hand, I have built-in a very strong battery (AGM).
In erlier times, the cranking/start logs are still working without a notebook (only with the flashpro!)
2008 Honda Civic TypeR FN2
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Re: Engine start logging not possible anymore?
Any news about this, Hondata?
2008 Honda Civic TypeR FN2
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Re: Engine start logging not possible anymore?
Try connecting a battery charger when starting to see if that allows it to datalog the start. If it does then you know it is a low battery voltage issue.
Re: Engine start logging not possible anymore?
Hondata, what is about this issues in Flashpro Manager:
#1:
If i upload a Map from the secondary storage from the Flashpro, the Flashpro always make a short datalog or save a short datalog to the Flashpro.
I think this which, because I have to press the "datalog-button" to upload a Map from secondary storage of the Flashpro!?
This problem/phenomenon I do not have, if I a upload a primary Map to the ECU or if i upload Maps (primary/secondary) with my notebook to the ECU, because I do not press the "datalog-button" in this case!
#2:
If i open a read-only Flashpro-Map over the Windows-Explorer to open in the Flashpro-Manager and would save this file in FlashPro Manager, the program (FlashPro-Manager) crashes.
If I would like to open the file directly in FlashPro-Manager, the message "read only" pops up!
#3:
I use Windows 10, but under "about" i only read -Windows 8- like this:
#1:
If i upload a Map from the secondary storage from the Flashpro, the Flashpro always make a short datalog or save a short datalog to the Flashpro.
I think this which, because I have to press the "datalog-button" to upload a Map from secondary storage of the Flashpro!?
This problem/phenomenon I do not have, if I a upload a primary Map to the ECU or if i upload Maps (primary/secondary) with my notebook to the ECU, because I do not press the "datalog-button" in this case!
#2:
If i open a read-only Flashpro-Map over the Windows-Explorer to open in the Flashpro-Manager and would save this file in FlashPro Manager, the program (FlashPro-Manager) crashes.
If I would like to open the file directly in FlashPro-Manager, the message "read only" pops up!
#3:
I use Windows 10, but under "about" i only read -Windows 8- like this:
2008 Honda Civic TypeR FN2
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Re: Engine start logging not possible anymore?
Thanks.
1. Press the program button before the datalog button.
2. We'll add another warning message.
3. We've already fixed this.
1. Press the program button before the datalog button.
2. We'll add another warning message.
3. We've already fixed this.
Hondata
Re: Engine start logging not possible anymore?
It does not matter if I press the "program-" or the "datalog-" button at first, if i would upload a secondary map?Hondata wrote:Thanks.
1. Press the program button before the datalog button.
2008 Honda Civic TypeR FN2
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Re: Engine start logging not possible anymore?
???
2008 Honda Civic TypeR FN2
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Rotrex C30-94 supercharged with relocated IAT
Powered by ASNU 092/FP330E fuel pump & ASNU 090/750cc fuel injectors
------------------------
ECU: 37820-RSP-E02
Flashpro: FP-SI-INT-21153
Software: 3.6.1.0
Firmware: 185
Re: Engine start logging not possible anymore?
Uploading from the FlashPro to the ECU
To upload a calibration which has been previously stored on the FlashPro:
1. Plug the FlashPro into the diagnostic connector and switch on the vehicle ignition.
• Primary calibration - press the Program button for at least one second.
• Secondary calibration - holding the Datalog button down, press the Program button for at least one second, releasing the Program button before the Datalog button.
To upload a calibration which has been previously stored on the FlashPro:
1. Plug the FlashPro into the diagnostic connector and switch on the vehicle ignition.
• Primary calibration - press the Program button for at least one second.
• Secondary calibration - holding the Datalog button down, press the Program button for at least one second, releasing the Program button before the Datalog button.