Bugs with Flashpro manager low cam fuel map

FlashPro Manager software
Post Reply
wildabeast
Posts: 13
Joined: Thu Dec 31, 2009 11:13 am
Contact:

Bugs with Flashpro manager low cam fuel map

Post by wildabeast » Wed Sep 05, 2012 10:22 am

I have been doing datalogging for the past few days and updated to flashpro manager 1.3.3 recently as well.
Without changing anything, all of a sudden the #7 column on all my low cam fuel maps are reading too lean.

I have my lambda overlay setup like this:
14.7 below -4.3psi
13.1 between
11.9 above 2.6psi

my #7 column is -7.6psi and #8 column is -4.3psi

stock sensor for closed loop
corrected stock sensor for open loop

by doing some quick calculations, it seems the #7 column is actually calculating for the 13.1 AFR instead of 14.7.
If calculating those columns for 14.7AFR, the calibration is just about spot on.
If calculating those columns for 13.1AFR, the lambda bug is spot on.

I can only confirm 0,15 and 30 degree cam angle fuel tables. I don't use 40 and 50 (even though they are roughly tuned for it)

I have a built k20z3 long block with more mods than I can count running on 20lbs of boost on the SRT kit on a CEA 6262SP, 10:1 compression, kelford stage1 turbo cams..

User avatar
Hondata
Site Admin
Posts: 8763
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Bugs with Flashpro manager low cam fuel map

Post by Hondata » Wed Sep 05, 2012 11:39 am

I've tested this here and everything looks ok.

I suggest you make the lambda overlay divisions fall between the load columns. eg make the lambda overlay lower value -4.4psi
Hondata

wildabeast
Posts: 13
Joined: Thu Dec 31, 2009 11:13 am
Contact:

Re: Bugs with Flashpro manager low cam fuel map

Post by wildabeast » Wed Sep 05, 2012 4:34 pm

here are some screenshots now that I am home, and I uploaded my calibration as well as 1 of the datalogs. I'll show more screenshots to show how the column is changing. It doesnt make sense.
Attachments
Untitled4.jpg
Untitled4.jpg (727.64 KiB) Viewed 2913 times
Untitled5.jpg
Untitled5.jpg (733.85 KiB) Viewed 2913 times
wildabeast FP settings.ini
(7.46 KiB) Downloaded 172 times
datalog0005.fpdl
(1.89 MiB) Downloaded 158 times
20120902 - boost duty.fpcal
(19.33 KiB) Downloaded 141 times

wildabeast
Posts: 13
Joined: Thu Dec 31, 2009 11:13 am
Contact:

Re: Bugs with Flashpro manager low cam fuel map

Post by wildabeast » Wed Sep 05, 2012 4:35 pm

And here's the rest of the screenshots.
Attachments
New Bitmap Image (2).jpg
New Bitmap Image (2).jpg (714.93 KiB) Viewed 2912 times
New Bitmap Image.jpg
New Bitmap Image.jpg (753.09 KiB) Viewed 2912 times
Untitled3.jpg
Untitled3.jpg (727.66 KiB) Viewed 2912 times

wildabeast
Posts: 13
Joined: Thu Dec 31, 2009 11:13 am
Contact:

Re: Bugs with Flashpro manager low cam fuel map

Post by wildabeast » Wed Sep 05, 2012 4:36 pm

notice when i change the low load from -4 to -3.9psi, it's all of a sudden ok.....
but going from -4 to -4.4 doesnt make as big of a difference, and yet my AFR's are right where they're suppose to be.

between image 2 and image 1, i change just the middle afr difference, and it changes the values OUTSIDE of that range.... does that make any sense??

User avatar
Hondata
Site Admin
Posts: 8763
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Bugs with Flashpro manager low cam fuel map

Post by Hondata » Thu Sep 06, 2012 5:39 pm

Can you send us the datalogs?
Hondata

wildabeast
Posts: 13
Joined: Thu Dec 31, 2009 11:13 am
Contact:

Re: Bugs with Flashpro manager low cam fuel map

Post by wildabeast » Mon Sep 10, 2012 9:33 am

where do you want me to send them to? I attached my FP settings, 1 of my datalogs and my calibration file in the 2nd post of this thread (check after the 2nd picture)

I can email/send where ever you'd like though.

User avatar
Spunkster
Site Admin
Posts: 17943
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Bugs with Flashpro manager low cam fuel map

Post by Spunkster » Mon Sep 10, 2012 11:01 am

Post the calibration and datalogs here. Screenshots are not enough

User avatar
Hondata
Site Admin
Posts: 8763
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Bugs with Flashpro manager low cam fuel map

Post by Hondata » Tue Sep 11, 2012 7:43 am

Hondata

Post Reply