Active Fuel Tuning (MAP)

FlashPro Manager software
Post Reply
trymion
Posts: 5
Joined: Tue Sep 19, 2017 10:52 am

Active Fuel Tuning (MAP)

Post by trymion » Fri Jan 05, 2018 11:31 am

FlashPro Manager version: 2.8.6
2006 Civic Si, slighty modified

Issue:

When trying to use "Active Fuel Tuning" (i.e. using MAP), I can't seem to download the changes the ECU is making into the calibration.

From a new calibration, these are the steps I've done:
Fuel > Uncheck "AFM Enabled", check "Use speed/density (map) fuel tables"
Fuel > Active Tuning > check "Active Fuel Tuning enabled"
Upload calibration to ECU.
Drive around for roughly 30 minutes.
Turn the car fully off.
Turn the ingition to the "ON" position.
Note: The second time I attempted this, I left the laptop on and flashpro plugged in.

Now here's where I get confused.

When I click "Download Active Tables from ECU" in either "Active Fuel Tuning Low" or "High" table, nothing gets updated. Everything (the Trim%) stays at 0.00. I've also tried "Merge active table into main tables" but there was also no difference in the adjustments.

What am I doing wrong?

Can someone list the proper way to use Active Fuel Tuning?

I've done Active AFM tuning (in Sensors > AFM > Active Fuel Tuning enabled) and after driving around for a short period of time, clicking "update Active Tuning Table" actually updated and changed flow values. I wanted to switch over to MAP and thought it would be as easy but it seems to be eluding me.

Thanks.

trymion
Posts: 5
Joined: Tue Sep 19, 2017 10:52 am

Re: Active Fuel Tuning (MAP)

Post by trymion » Fri Jan 05, 2018 1:04 pm

I updated my FlashPro manager to 2.8.7 and re-enabled fuel tuning from a new calibration (like the steps i did above).

I drove around for approx 40m and when i clicked the "download tables from ecu" button, it didn't update anything again.

trymion
Posts: 5
Joined: Tue Sep 19, 2017 10:52 am

Re: Active Fuel Tuning (MAP)

Post by trymion » Fri Jan 05, 2018 1:21 pm

Sorry for multiple replies but i always run out of time to edit the other posts, or i just don't see the edit button any longer.

I'm not sure if this will help, but this is the recent datalog from the drive i mentioned in the previous post.
also I'm including the calibration file I'm using.
Attachments
aft01_36Minutes.fpdl
(484.65 KiB) Downloaded 24 times
Eclaire_pmallcai_norevhang-nodelay-vtctable_map01.fpcal
(21.92 KiB) Downloaded 31 times

herkikile
Posts: 4
Joined: Sat Dec 02, 2017 9:42 am

Re: Active Fuel Tuning (MAP)

Post by herkikile » Wed Jan 17, 2018 4:12 pm

trymion wrote:
Fri Jan 05, 2018 11:31 am
FlashPro Manager version: 2.8.6
2006 Civic Si, slighty modified

Issue:

When trying to use "Active Fuel Tuning" (i.e. using MAP), I can't seem to download the changes the ECU is making into the calibration.

From a new calibration, these are the steps I've done:
Fuel > Uncheck "AFM Enabled", check "Use speed/density (map) fuel tables"
Fuel > Active Tuning > check "Active Fuel Tuning enabled"
Upload calibration to ECU.
Drive around for roughly 30 minutes.
Turn the car fully off.
Turn the ingition to the "ON" position.
Note: The second time I attempted this, I left the laptop on and flashpro plugged in.

Now here's where I get confused.

When I click "Download Active Tables from ECU" in either "Active Fuel Tuning Low" or "High" table, nothing gets updated. Everything (the Trim%) stays at 0.00. I've also tried "Merge active table into main tables" but there was also no difference in the adjustments.

What am I doing wrong?

Can someone list the proper way to use Active Fuel Tuning?

I've done Active AFM tuning (in Sensors > AFM > Active Fuel Tuning enabled) and after driving around for a short period of time, clicking "update Active Tuning Table" actually updated and changed flow values. I wanted to switch over to MAP and thought it would be as easy but it seems to be eluding me.

Thanks.
When you're ready to upload the modified calibration to the ecu turn the key back one click(that turns the engine off but keeps all the computers up). Wait a few seconds then turn it forward one click but do not start the car. Now upload to ecu
boosted 2013 civic r18

trymion
Posts: 5
Joined: Tue Sep 19, 2017 10:52 am

Re: Active Fuel Tuning (MAP)

Post by trymion » Fri Jan 19, 2018 10:32 am

That's not the issue I am having as I do know how to upload a calibration and have been trying to self tune my vehicle.

My issue is that Fuel Active Tuning doesn't seem to be working, whereas AFM Active Tuning is.

Thanks for the reply, though.

joecang
Posts: 3
Joined: Sun Mar 12, 2017 8:52 pm

Re: Active Fuel Tuning (MAP)

Post by joecang » Mon Jan 22, 2018 9:29 pm

I, too, have the same issue. I can't seem to download the ECU active table. I just get 0 everytime I download from ECU.

arraydude
Posts: 31
Joined: Tue Aug 13, 2013 8:25 pm
Location: Argentina

Re: Active Fuel Tuning (MAP)

Post by arraydude » Mon Jun 04, 2018 12:34 pm

same here

User avatar
Hondata
Site Admin
Posts: 8337
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Active Fuel Tuning (MAP)

Post by Hondata » Mon Jun 04, 2018 4:02 pm

You have to save the calibration immediately after upload and then load the same calibration before downloading the changes.
Hondata

arraydude
Posts: 31
Joined: Tue Aug 13, 2013 8:25 pm
Location: Argentina

Re: Active Fuel Tuning (MAP)

Post by arraydude » Tue Jun 05, 2018 12:42 pm

just to summarize it..

So, in order to get this working do i have to... :

1- Upload the calibration
2- Save it again after uploading it, *do i have to store it in a different location?*
3- Go and ride with the car
4- Open the last saved cal and click on the download button from the active tuning table?

myuser
Posts: 65
Joined: Sat Jun 27, 2009 6:55 am

Re: Active Fuel Tuning (MAP)

Post by myuser » Sun Jun 10, 2018 6:47 am

Just to share the process...
https://www.youtube.com/watch?v=TLDR6-thsG8

arraydude
Posts: 31
Joined: Tue Aug 13, 2013 8:25 pm
Location: Argentina

Re: Active Fuel Tuning (MAP)

Post by arraydude » Mon Jun 25, 2018 12:05 pm

thanks for sharing

Post Reply