Flashpro Manager 3.2.8.0 version box error

FlashPro Manager software
Post Reply
Rush
Posts: 14
Joined: Tue Apr 02, 2019 2:12 pm

Flashpro Manager 3.2.8.0 version box error

Post by Rush » Tue Apr 02, 2019 2:45 pm

hondata 1.JPG
hondata 1.JPG (130.6 KiB) Viewed 1157 times
Flashpro seems to have a conflict with the current 3.2.8.0 Manager. Tune seems to have loaded correctly.

User avatar
Spunkster
Site Admin
Posts: 17582
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Flashpro Manager 3.2.8.0 version box error

Post by Spunkster » Tue Apr 02, 2019 3:36 pm

Are you getting this message after you have uploaded to the ECU using 3.2.8 software?

Rush
Posts: 14
Joined: Tue Apr 02, 2019 2:12 pm

Re: Flashpro Manager 3.2.8.0 version box error

Post by Rush » Tue Apr 02, 2019 3:56 pm

It happens when I connect the Flashpro to the computer. The Flashpro had the tune loaded on 3.2.8.0. I deleted the tune and reloaded 3 times to the Flashpro and same box appears each time.

User avatar
Spunkster
Site Admin
Posts: 17582
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Flashpro Manager 3.2.8.0 version box error

Post by Spunkster » Tue Apr 02, 2019 4:09 pm

But did you actually upload the calibration to the ECU?

Rush
Posts: 14
Joined: Tue Apr 02, 2019 2:12 pm

Re: Flashpro Manager 3.2.8.0 version box error

Post by Rush » Tue Apr 02, 2019 4:19 pm

Yes. It took 2 tries. First had an engine light emission code. Second try all went well, no errors.

User avatar
Spunkster
Site Admin
Posts: 17582
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Flashpro Manager 3.2.8.0 version box error

Post by Spunkster » Tue Apr 02, 2019 5:04 pm

And it is telling you the calibration is still out of date after uploading to the ECU now?

Rush
Posts: 14
Joined: Tue Apr 02, 2019 2:12 pm

Re: Flashpro Manager 3.2.8.0 version box error

Post by Rush » Tue Apr 02, 2019 5:10 pm

Correct. Each time I connect the Flashpro to the Manager the box appears.

nappco
Posts: 23
Joined: Wed Mar 27, 2019 4:30 am

Re: Flashpro Manager 3.2.8.0 version box error

Post by nappco » Wed Apr 03, 2019 4:38 am

....2018 Hatch MT

I have the same message. It started for me when I updated a few weeks or so with version 3.2.6. I hadn't touched it or reflashed since last summer. I also had an update error that reported with 3.2.6 when I was flashing the ECU... about 1/4 into the flash it said there was an error, then after a min it started reloading again.I think the upload didn't take. The Hondata Mode seemed to be stock tuning. I have no screen shots.

I updated with 3.2.8.0 last night and haven't had a chance to see if the tune is good.

nappco
Posts: 23
Joined: Wed Mar 27, 2019 4:30 am

Re: Flashpro Manager 3.2.8.0 version box error

Post by nappco » Wed Apr 03, 2019 4:43 pm

Well, I think there is a firmware problem. I flashed my original tune and its still not correct. I've attached the tune from July 2018. I think there is a problem with either the traction control or boost by gear. Hope this helps
Attachments
Jason after 1 month.fpcal
(9.26 KiB) Downloaded 8 times

User avatar
Hondata
Site Admin
Posts: 8589
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Flashpro Manager 3.2.8.0 version box error

Post by Hondata » Wed Apr 03, 2019 5:22 pm

The message 'Calibrations stored on the FlashPro are from a previous ...' is normal after an update.
Hondata

nappco
Posts: 23
Joined: Wed Mar 27, 2019 4:30 am

Re: Flashpro Manager 3.2.8.0 version box error

Post by nappco » Wed Apr 03, 2019 5:58 pm

Thanks, any thoughts on the update? There was a major downgrade in performance after this update.

nappco
Posts: 23
Joined: Wed Mar 27, 2019 4:30 am

Re: Flashpro Manager 3.2.8.0 version box error

Post by nappco » Thu Apr 04, 2019 4:04 am

I put the factory tune back in and verified the new version is not working correctly. There is no difference in performance.

Post Reply