Hondata Flashpro P0134 error code

FlashPro questions & answers specific to the 2006-2009 (US, UK, Asia) S2000
keithd2959
Posts: 50
Joined: Tue May 08, 2012 8:45 am

Hondata Flashpro P0134 error code

Post by keithd2959 »

Hi all,

I own a European 2006 S2000 donor engine on my race car with Hondata Flashpro. I am having an error code P0134 which is sending the car in limp mode (with P2101).The secondary oxygen sensor was removed and disabled by the Hondata, but as far as I am learning the P0134 comes on with an ECU check and affects the primary oxygen sensor too, which in my case is fitted.
I went through the Hondata forums and there were suggestions to enable " disable P0134",but I could not find this option on my Flashpro.
Any suggestions please?
Thank you

User avatar
Hondata
Site Admin
Posts: 9278
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Hondata Flashpro P0134 error code

Post by Hondata »

Do you have a primary sensor? Is it disabled in the calibration?
Hondata

keithd2959
Posts: 50
Joined: Tue May 08, 2012 8:45 am

Re: Hondata Flashpro P0134 error code

Post by keithd2959 »

Hi yes i have a primary sensor and the 2nd sensor is disabled but for a reason it seems like the ecu is still doing the tests for both sensors.

This is a race car, is there a way how i can disable all the internal tests? Thanks

User avatar
Hondata
Site Admin
Posts: 9278
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Hondata Flashpro P0134 error code

Post by Hondata »

P0134 relates to the primary sensor. Is it disabled in the calibration?
Hondata

keithd2959
Posts: 50
Joined: Tue May 08, 2012 8:45 am

Re: Hondata Flashpro P0134 error code

Post by keithd2959 »

No, the primary sensor is still enabled as i am using it for closed loop. If i disable it will i still have this function? Thanks

User avatar
Hondata
Site Admin
Posts: 9278
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Hondata Flashpro P0134 error code

Post by Hondata »

Sorry, I missed that you still had the primary o2. P0134 is an error relating to the primary o2 sensor heater. Either the sensor is bad or there is a break in the wiring.
Hondata

keithd2959
Posts: 50
Joined: Tue May 08, 2012 8:45 am

Re: Hondata Flashpro P0134 error code

Post by keithd2959 »

Many thanks for your reply, i really appreciate. My primary o2 sensor is brand new, less than 100 miles old cause my old one was sending a heater fault. The strange thing is that the error is showing as " o2 sensor circuit no activity bank1 sensor 1 ". Then when you reset the ecu the problem goes away for a while and the sensor works fine.

User avatar
Hondata
Site Admin
Posts: 9278
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Hondata Flashpro P0134 error code

Post by Hondata »

Honda lists P0134 as 'Air/Fuel Ratio (A/F) Sensor (Sensor 1) Heater System Malfunction'. FlashPro has the generic OBDII message of 'O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)'.
Hondata

keithd2959
Posts: 50
Joined: Tue May 08, 2012 8:45 am

Re: Hondata Flashpro P0134 error code

Post by keithd2959 »

Thanks for the info. So you suggest that the fault is from the primary O2 sensor, either the wiring or the sensor itself correct?

User avatar
Hondata
Site Admin
Posts: 9278
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Hondata Flashpro P0134 error code

Post by Hondata »

Yes. It usually is the heater if it is the o2 itself, or the wiring otherwise.
Hondata

keithd2959
Posts: 50
Joined: Tue May 08, 2012 8:45 am

Re: Hondata Flashpro P0134 error code

Post by keithd2959 »

Thanks for the information. Although my primary sensor is new, do you suggest a part number that is good for my application as an original one from a local dealer is ridiculosly expensive. I have a 2006 european s2000 engine. Thanks

User avatar
Hondata
Site Admin
Posts: 9278
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Hondata Flashpro P0134 error code

Post by Hondata »

Sorry, there's no substitute o2 sensor that I know of for the s2000.
Hondata

keithd2959
Posts: 50
Joined: Tue May 08, 2012 8:45 am

Re: Hondata Flashpro P0134 error code

Post by keithd2959 »

Thanks

keithd2959
Posts: 50
Joined: Tue May 08, 2012 8:45 am

Re: Hondata Flashpro P0134 error code

Post by keithd2959 »

Just to be sure that my sensor is compatible with my engine ,this is the part No. Denso 234-9065.It has four wires: blue,white and two black. Can you kindly confirm? tks

User avatar
Hondata
Site Admin
Posts: 9278
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: Hondata Flashpro P0134 error code

Post by Hondata »

There's no definitive cross reference from Denso to the Honda part number that I know of.
Hondata

Post Reply