TSX 04-06 green connector

FlashPro questions & answers specific to the 2007-2008 US TSX
Post Reply
Zoro2006
Posts: 119
Joined: Sun May 02, 2010 3:07 am

TSX 04-06 green connector

Post by Zoro2006 » Fri Feb 10, 2012 8:35 am

Anybody can explain if this correct green connector ? Above glove box apartament, didn't had a tester to check :)

Image
Known as Vaikis_

sass
Posts: 104
Joined: Mon Oct 06, 2008 5:07 am
Location: Evropa-Estonia-Tallinn

Re: TSX 04-06 green connector

Post by sass » Mon Feb 13, 2012 9:11 am

Cr-v RD8+K24A2turbo+Kpro V4 prb+NPR3/6Speed+ТС+ HFS4 v3.2.
DynoWheel = 472kW / 589 N.m
HRX One Mile Challenge = Max Speed 282km
Known as Sniper

Zoro2006
Posts: 119
Joined: Sun May 02, 2010 3:07 am

Re: TSX 04-06 green connector

Post by Zoro2006 » Mon Feb 13, 2012 9:47 am

Known as Vaikis_

lamerchebg
Posts: 2
Joined: Thu Sep 18, 2014 2:22 pm

Re: TSX 04-06 green connector

Post by lamerchebg » Thu Sep 18, 2014 3:05 pm

Hi Zoro2006 sorry to border you but i recently bought a tsx ecu and a flashpro and i am about to do the CAN programming adapter installation on my 2006 accord 2.4 executive( german version) and i followed the instructions and unmounted the glove box but like you i have two green connectors:number 1 and 2 in the picture that i attached,so my question is did you use the number 1 connector or the number 2 connector as described in the hondata manual :
http://www.hondata.com/downloads/04-06_ ... nstall.pdf

also i wanted to ask you did you do it exactly as described in the hondata manual or did you use an other approach(i am asking cause if i have to do it following the hondata manual and use connector number 2, i would have to solder the two wires to the green connector cause on my green connector there is no empty spot),and also is there something else(except everything mentioned in the hondata manual) i should do before going to the honda dealer for the VIN and immobilizer matching.

once again sorry to border you.thanks a lot best regards Todor
Attachments
green connector.jpg
green connector.jpg (109.47 KiB) Viewed 5004 times

Zoro2006
Posts: 119
Joined: Sun May 02, 2010 3:07 am

Re: TSX 04-06 green connector

Post by Zoro2006 » Thu Oct 09, 2014 6:08 am

lamerchebg wrote:Hi Zoro2006 sorry to border you but i recently bought a tsx ecu and a flashpro and i am about to do the CAN programming adapter installation on my 2006 accord 2.4 executive( german version) and i followed the instructions and unmounted the glove box but like you i have two green connectors:number 1 and 2 in the picture that i attached,so my question is did you use the number 1 connector or the number 2 connector as described in the hondata manual :
http://www.hondata.com/downloads/04-06_ ... nstall.pdf

also i wanted to ask you did you do it exactly as described in the hondata manual or did you use an other approach(i am asking cause if i have to do it following the hondata manual and use connector number 2, i would have to solder the two wires to the green connector cause on my green connector there is no empty spot),and also is there something else(except everything mentioned in the hondata manual) i should do before going to the honda dealer for the VIN and immobilizer matching.

once again sorry to border you.thanks a lot best regards Todor
number 2
Known as Vaikis_

majork
Posts: 10
Joined: Sun Feb 10, 2013 6:12 am

Re: TSX 04-06 green connector

Post by majork » Thu Oct 09, 2014 7:10 am

or a bridge on the can bus just before the ecu in the center lower dash ....like i do with solder and clips.... less effort and cut on hands

Post Reply