TC with other management system

Post Reply
BEKA-BEKA
Posts: 17
Joined: Sat Apr 09, 2011 10:15 am

TC with other management system

Post by BEKA-BEKA » Mon Oct 02, 2017 7:47 am

I have additional maps for fuel and ignition table with O2 voltage as the load index with the engine management I have. Can I use an O2 sensor 0-5voltage input from this ECU with Hondata Traction Control 0-5v output?

User avatar
Hondata
Site Admin
Posts: 8783
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: TC with other management system

Post by Hondata » Mon Oct 02, 2017 11:23 am

That is a question you need to ask the other management system. The TC can provide a 0-5V signal for slip.
Hondata

BEKA-BEKA
Posts: 17
Joined: Sat Apr 09, 2011 10:15 am

Re: TC with other management system

Post by BEKA-BEKA » Sat Nov 18, 2017 10:37 am

For Honda Civic 2006+, Do we use the Active Wheel Speed Sensor Wiring method, where we cut -'ve wire, strip and join to the Traction Control module input?

User avatar
Hondata
Site Admin
Posts: 8783
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: TC with other management system

Post by Hondata » Sat Nov 18, 2017 9:17 pm

Yes, the 06 Civic has active sensors.
Hondata

BEKA-BEKA
Posts: 17
Joined: Sat Apr 09, 2011 10:15 am

Re: TC with other management system

Post by BEKA-BEKA » Tue Nov 28, 2017 4:31 am

Hence, We only need to cut 4 wires on the ABS controller harness, i.e. FL-GND, FR-GND, RL-GND and RR-GND, right? And connect the FL-GND that has been cut to FL- and FL+ of the Hondata TC wiring with no polarity? And do the same with the other three cut cables, right?

User avatar
Hondata
Site Admin
Posts: 8783
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: TC with other management system

Post by Hondata » Tue Nov 28, 2017 7:21 am

Yes, see
Image
Hondata

BEKA-BEKA
Posts: 17
Joined: Sat Apr 09, 2011 10:15 am

Re: TC with other management system

Post by BEKA-BEKA » Tue Nov 28, 2017 8:48 am

I was using the connector wiring on the reference on the help file, where it uses all the + and - of the wheel sensor wiring. I've cut a couple of + cables till I realized only the -GND cables would be used.

BTW, Can we use the IGN1+ on the ABS Controller harness for the power?

User avatar
Spunkster
Site Admin
Posts: 18022
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: TC with other management system

Post by Spunkster » Tue Nov 28, 2017 11:08 am

It is best to use the power and grounds at the ECU to avoid ground loops and voltage offsets.

BEKA-BEKA
Posts: 17
Joined: Sat Apr 09, 2011 10:15 am

Re: TC with other management system

Post by BEKA-BEKA » Thu Nov 30, 2017 8:16 pm

With the 0-5v analog output from the Hondata TC orange wire, How can we relate this to the Slip (%)?
Does this mean increase in the analog voltage output also mean increase on the Slip (%)?

User avatar
Hondata
Site Admin
Posts: 8783
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: TC with other management system

Post by Hondata » Fri Dec 01, 2017 8:56 am

You can configure the output voltage in the software. The output voltage is proportional to over slip (not slip).
Hondata

BEKA-BEKA
Posts: 17
Joined: Sat Apr 09, 2011 10:15 am

Re: TC with other management system

Post by BEKA-BEKA » Sat Dec 16, 2017 10:22 pm

Can we still use the traction switch if the traction control is used with other standalone ecu? Do you have any suggestions on how to connect them together?

User avatar
Hondata
Site Admin
Posts: 8783
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: TC with other management system

Post by Hondata » Sun Dec 17, 2017 8:51 pm

Yes. Connect what together?
Hondata

dc5itr01
Posts: 30
Joined: Tue May 24, 2016 2:14 pm

Re: TC with other management system

Post by dc5itr01 » Mon Oct 14, 2019 9:36 am

I would also like to connect hondata tc to aftermarket ecu.
This ecu can only cut spark if given a signal as to when it should cut. And it can cut for a predetermined duration.
But it cannot sense any difference between 1v and 5v from hondata tc.
Can the hondata tc perhaps pulse this output in relation to the amount of spark cut required based on slip read?
Or is there another way of this working?

User avatar
Spunkster
Site Admin
Posts: 18022
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: TC with other management system

Post by Spunkster » Mon Oct 14, 2019 9:43 am

No, this is not possible.

Post Reply