k20z2

FlashPro Manager software
Post Reply
yeuror
Posts: 3
Joined: Thu Dec 31, 2009 10:10 am

k20z2

Post by yeuror »

what about this engine type? is available the flash pro or anything else about programming?
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Post by Spunkster »

What vehicle is this and what is the ECU code?
ajpturbopittsburgh
Posts: 145
Joined: Wed May 26, 2010 10:58 am

Post by ajpturbopittsburgh »

K20Z2
Found in:
2006- Acura CSX (Canada)
Displacement: 1,998 cc (121.9 cu in)
Compression: 9.6:1
Power: 155 hp (114 kW) @ 6000 rpm (SAE net J1349 Rev 8/04)
Torque: 139 ft·lbf (188 N·m) @ 4500 rpm
Redline: 6800 rpm


2006- Honda Civic (JDM)
Displacement: 1,998 cc (121.9 cu in)
Compression: 9.6:1
Power: 155 hp (114 kW) @ 6000 rpm
Torque: 139 ft·lbf (188 N·m) @ 4500 rpm
Redline: 6800 rpm


2006- Honda Accord(Europe)
Displacement: 1998 cc
Compression: 9.6:1
Power: 155 hp (114 kW) @ 6000 rpm
Torque: 139 ft·lbf (188 N·m) @ 4500 rpm
Redline: 6800 rpm
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Post by Spunkster »

m_leavy
Posts: 4
Joined: Mon Feb 12, 2018 9:53 am

Re: k20z2

Post by m_leavy »

Can i run a turbo setup on this engine with a PRA ecu
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: k20z2

Post by Spunkster »

What vehicle is this in?
m_leavy
Posts: 4
Joined: Mon Feb 12, 2018 9:53 am

Re: k20z2

Post by m_leavy »

Spunkster its hopefully going in a mazda rx8
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: k20z2

Post by Spunkster »

Is this drive by wire?
m_leavy
Posts: 4
Joined: Mon Feb 12, 2018 9:53 am

Re: k20z2

Post by m_leavy »

I think it is but haven't checked yet. there are a couple of guys from Poland that have done it with the k20z4 just one is using hondata and the other is using an emu engine management system. however my polish is no good so I was looking for a pin out for a PRA ecu as I can only find picture upon picture for US compatible ecus
User avatar
Spunkster
Site Admin
Posts: 22737
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: k20z2

Post by Spunkster »

IF it is drive by wire we do not offer anything that will work with that in an engine swap.
m_leavy
Posts: 4
Joined: Mon Feb 12, 2018 9:53 am

Re: k20z2

Post by m_leavy »

all im looking for is a pin out for the pra ecu
Post Reply