s300 hardware problem

Hondata installation questions / answers / issues.
integra_22t
Posts: 29
Joined: Tue May 01, 2012 8:04 am

Re: s300 hardware problem

Post by integra_22t »

pulled eveything out and installed into anouther ecu and 2 green lights .. tomorow ill upload the tune and see what happens
integra_22t
Posts: 29
Joined: Tue May 01, 2012 8:04 am

Re: s300 hardware problem

Post by integra_22t »

well started the car and let it sit till the rad fan to come on and 5 min into it the car dies and when it happens my temps go to 302 again and the rpm goes to 52,427

and only one green light again

i dont know what to do at this point :(
Attachments
june5.s3d
(1.85 MiB) Downloaded 327 times
last tune.skl
(37.98 KiB) Downloaded 311 times
integra_22t
Posts: 29
Joined: Tue May 01, 2012 8:04 am

Re: s300 hardware problem

Post by integra_22t »

well im in to the 3rd ecu now .. a chiped p28 ... removed the ic chip and the ic mount .. installed the male pins for the hondata in to the 24 pin slot (27256 - ic4) and the 4 pins (icn2) into the chiped ecu and removed j12

Image

Image



it already had the jumper at j1, resistor at r54 and 74373 ic at ic4

Image

put the hondata in and still no green light at d2

Image

so i pull the hondata out and reinstall the chip back into the ecu by conecting 2 ic mounts together and reconecting j12 the ecu acts normal

Image

Image

pull the chip out and put the hondata back in and 1 green light :(

also traced all conections from the top side of the hondata to all conections on the ic4 (373) and the 66k ic and all where fine ( thanks for the pin out )

Image

also i know its not a bad solder joint as the chip works fine
User avatar
Spunkster
Site Admin
Posts: 22741
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: s300 hardware problem

Post by Spunkster »

Out of curiosity have you tried this ECU/s300 in a different vehicle?

It is very strange that this only happens after the fans come on and it gets up to temperature.
integra_22t
Posts: 29
Joined: Tue May 01, 2012 8:04 am

Re: s300 hardware problem

Post by integra_22t »

yes i tried it in a bone stock 95 integra b18b and my own 95 integra with an h22 swaped and chiped ecu

its not happing when the fan comes on ... that is when the 2nd one stoped working .. now with the 3rd ecu dosent light up d2 at all

but works fine with the chip installed .. infact i drove it into the shop



now you said when you dont get a light at d2 its a conector (solder) problem ... but its fine with the burnt chip so wtf ?

im at a month now with no car to give to the customer .. down 3 ecu's ....


so what do i do now ?
User avatar
Spunkster
Site Admin
Posts: 22741
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata

Re: s300 hardware problem

Post by Spunkster »

Don't replay to this thread.

Please email support <at> hondata.com with the following and a link to this thread and I will issue an RMA and give you further
instructions:

Name:
Address:
Phone:
Email:
Serial#:
integra_22t
Posts: 29
Joined: Tue May 01, 2012 8:04 am

Re: s300 hardware problem

Post by integra_22t »

whent back and chiped the 2nd ecu i was useing .. works fine with the chip .. one green light with the s300 and sent off email
Post Reply