Car jerks at low speed, less than 25km/h, gear2

FlashPro questions & answers specific to the 2010 CR-Z (US, Euro & Asia)
Post Reply
terenceng
Posts: 42
Joined: Thu Jan 14, 2010 11:19 am

Car jerks at low speed, less than 25km/h, gear2

Post by terenceng » Sun Jun 30, 2013 8:48 am

Dear Sirs,

I am using ASEAN RTW-P02 ECU with Flashpro.

My car just tuned by my tuner not long ago, but sometime my car likes to jerk or hesitate when rolling in 1st or 2nd gear at low speed.

Especially when I passing over a hump, press the gas enough to keep the car moving but it acts like its not getting any gas, no power and then all of a sudden jerks forward. To avoid jerky issue, most of the time i have to change the gear from 2 to 1 and accelerate the speed to more than 25km/h and then change to gear 2. It makes me look like I dont know how to drive a stick and its really making me mad.

I give it gas and it just sits there for a second and doesnt do anything and then BAM it just jerk and accels hard for a second. It runs fine when I'm at speed > 25kmh, highway cruising, high speed > 140km/h and really pushing it, has a smooth idle, and no check engine lights.

FYI, my mechanic has removed the second O2 sensor and has disable the error engine check light (should be emission check light error); My car running Rotrex C15-60 supercharger.

Anything can be done to the Flashpro?

Is it a tuning issue? or hardware issue? can it be solved by adjusting the ignition or fuel maps?

Thank you,

User avatar
Spunkster
Site Admin
Posts: 18012
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Car jerks at low speed, less than 25km/h, gear2

Post by Spunkster » Mon Jul 01, 2013 9:41 am

post the calibration used as well as a datalog showing the problem.

terenceng
Posts: 42
Joined: Thu Jan 14, 2010 11:19 am

Re: Car jerks at low speed, less than 25km/h, gear2

Post by terenceng » Sun Jul 07, 2013 8:17 am

Hi Spunkster,

My appreciations,

Terence Ng
Last edited by terenceng on Sun Jul 07, 2013 8:21 am, edited 2 times in total.

terenceng
Posts: 42
Joined: Thu Jan 14, 2010 11:19 am

Re: Car jerks at low speed, less than 25km/h, gear2

Post by terenceng » Sun Jul 07, 2013 8:18 am

Hi Spunkster,

Sorry for late reply as I am recently busy and outstation.

I've recently changed my rims (Forged and Light) and captured this log file at night.

The jerk issue is very minus during night time and I am not sure why..

Attached the calibration and short log file for your kindly helps.

If you need full pull log file or any other just let me know.

Thank you very much.

My appreciations,
Terence Ng
Attachments
datalog0002.fpdl
(23.34 KiB) Downloaded 270 times
Last edited by terenceng on Tue Jul 09, 2013 11:29 am, edited 1 time in total.

User avatar
Spunkster
Site Admin
Posts: 18012
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Car jerks at low speed, less than 25km/h, gear2

Post by Spunkster » Mon Jul 08, 2013 4:40 pm

What do you mean it is very minus at night?

terenceng
Posts: 42
Joined: Thu Jan 14, 2010 11:19 am

Re: Car jerks at low speed, less than 25km/h, gear2

Post by terenceng » Mon Jul 08, 2013 4:48 pm

Spunkster wrote:What do you meam it is very minus at night?

The jerk issue is not obvious at night.

I will attach another short log file to you soon.

Thank you,

terenceng
Posts: 42
Joined: Thu Jan 14, 2010 11:19 am

Re: Car jerks at low speed, less than 25km/h, gear2

Post by terenceng » Mon Jul 08, 2013 5:30 pm

Perhaps i am not sure is it because of my new changed light weight forced rims.

Just for your information.

Thank you,

User avatar
Spunkster
Site Admin
Posts: 18012
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Car jerks at low speed, less than 25km/h, gear2

Post by Spunkster » Tue Jul 09, 2013 11:10 am

In the fuel section of the calibratoin window, try lowering the values for the overrun fuel cut delay.

terenceng
Posts: 42
Joined: Thu Jan 14, 2010 11:19 am

Re: Car jerks at low speed, less than 25km/h, gear2

Post by terenceng » Tue Jul 09, 2013 11:29 am

Spunkster wrote:In the fuel section of the calibratoin window, try lowering the values for the overrun fuel cut delay.
Hi Spunkster, thanks for your reply!

I've found the setting window, however appreciate if you could enlighten me how much of the values should I set?

The default value for stock crz asia calibration is 70 for 1-5 gears and I used it in my new DYNO tuned calibration.

Shall I adjust the value for 1 gear to 69 or lower?

Attached another log files for your reference only.

Thank you so much!
Attachments
datalog0000.fpdl
(178.91 KiB) Downloaded 285 times
datalog0001.fpdl
(53.27 KiB) Downloaded 244 times
Last edited by terenceng on Tue Jul 09, 2013 11:59 am, edited 1 time in total.

User avatar
Spunkster
Site Admin
Posts: 18012
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Car jerks at low speed, less than 25km/h, gear2

Post by Spunkster » Tue Jul 09, 2013 11:37 am

Just start lowering the values by 10 or 20 and see what works best for you.

terenceng
Posts: 42
Joined: Thu Jan 14, 2010 11:19 am

Re: Car jerks at low speed, less than 25km/h, gear2

Post by terenceng » Tue Jul 09, 2013 11:47 am

Thanks, will test it out accordingly.

Gustavo424
Posts: 5
Joined: Mon Sep 17, 2018 4:57 pm

Re: Car jerks at low speed, less than 25km/h, gear2

Post by Gustavo424 » Thu Feb 14, 2019 11:58 am

was this issue ever fixed? im having the same problem in my car. honda civic si 2012, PRL short ram, invidia N1 catback exhaust (no downpipe). tuned on the dyno by a professional tuner, car runs perfect but has the same jerk at low speeds as described above. please HELP!!

User avatar
Spunkster
Site Admin
Posts: 18012
Joined: Fri Sep 20, 2002 5:06 pm
Location: Hondata
Contact:

Re: Car jerks at low speed, less than 25km/h, gear2

Post by Spunkster » Thu Feb 14, 2019 12:06 pm

Have you tried what was suggested above?

Post Reply