KPro / KManager requests

K-Series Programmable ECU installation questions / support issues
Knox
Posts: 122
Joined: Mon Jun 06, 2011 6:01 pm

Re: KPro / KManager requests

Post by Knox » Fri Mar 04, 2016 6:01 am

hondata or spunkster,

Do you think or possible to add these features kmanager in near future?
1. ignition cut (great sound at rev limiter)
2. rev limit by gear (like s300)
3. cold start target idle like s300 ect vs rpm

User avatar
Hondata
Site Admin
Posts: 8771
Joined: Thu Aug 15, 2002 12:13 pm
Location: Torrance, CA
Contact:

Re: KPro / KManager requests

Post by Hondata » Fri Mar 04, 2016 10:15 am

1. No.
2. Yes.
3. Maybe.
Hondata

Knox
Posts: 122
Joined: Mon Jun 06, 2011 6:01 pm

Re: KPro / KManager requests

Post by Knox » Wed Mar 09, 2016 6:24 am

Hondata wrote:1. No.
2. Yes.
3. Maybe.

Is it possible to add a feature for launch control like after releasing the clutch pedal contiues to limit the rev for additional time(seconds)?
Like after releasing the clutch pedal engine continous to cut for additional 2,3,etc seconds for eliminating the too much wheel spin at launch.

cd2781
Posts: 8
Joined: Mon Mar 28, 2016 4:59 pm

Re: KPro / KManager requests

Post by cd2781 » Wed Apr 06, 2016 5:35 am

Innovate LC-2 compatability?
After cranking fuel trims. Mine tends to go lean right as it starts up after cranking. But i had to remove fuel to keep it from dying at first

sass
Posts: 104
Joined: Mon Oct 06, 2008 5:07 am
Location: Evropa-Estonia-Tallinn

Re: KPro / KManager requests

Post by sass » Sun Apr 10, 2016 11:10 am

Hondata wrote:Max vehicle speed would be easier, but would just maximum gear be better still?
How are you?
Cr-v RD8+K24A2turbo+Kpro V4 prb+NPR3/6Speed+ТС+ HFS4 v3.2.
DynoWheel = 472kW / 589 N.m
HRX One Mile Challenge = Max Speed 282km
Known as Sniper

cpl racing
Posts: 21
Joined: Thu Apr 29, 2004 12:13 am
Location: United Kingdom
Contact:

Re: KPro / KManager requests

Post by cpl racing » Wed May 04, 2016 6:35 am

Is it possible to add a feature for launch control like after releasing the clutch pedal contiues to limit the rev for additional time(seconds)?
Like after releasing the clutch pedal engine continous to cut for additional 2,3,etc seconds for eliminating the too much wheel spin at launch.


You can do this by increasing the speed
Hondata, Jackson Racing, Gruppe M, Dyno Dynamics

Knox
Posts: 122
Joined: Mon Jun 06, 2011 6:01 pm

Re: KPro / KManager requests

Post by Knox » Wed May 04, 2016 6:46 am

cpl racing wrote:Is it possible to add a feature for launch control like after releasing the clutch pedal contiues to limit the rev for additional time(seconds)?
Like after releasing the clutch pedal engine continous to cut for additional 2,3,etc seconds for eliminating the too much wheel spin at launch.


You can do this by increasing the speed

I tried it before but I did not have a result I need. I think its because of, ecu reads from vss and when front wheels spinging launch speed limit reached and launch control disables automatically. When I used high launch speed this time ecu holds the car at launch control all the time (like revlimit). I think you can use it on UK because of better tarmac traction but here in Cyprus I can not use because tarmac is too bad and there is too much wheel spin and launch speed limit reached immediaetly. So if there is lets say 3-5 seconds launch cut continous after launch that will be perfect.

I think on motec (fully enabled one) you can select to use the speed sensor (rear or front, for ex: on a fwd car you select rear wheels to determine speed and launch still cuts when that determined speed reached) or simply put a time like 3-5seconds on 4wd cars.

Korn4900
Posts: 16
Joined: Mon Apr 25, 2016 6:17 pm

Re: KPro / KManager requests

Post by Korn4900 » Mon May 09, 2016 3:13 pm

DBW support for traction control? I know not a complicated this to ad but the biggest thing is the console from the kpro after you wire the console unit TB and throttle sensor

Is this possible?

civic1234
Posts: 23
Joined: Wed Jan 15, 2014 10:57 am

Re: KPro / KManager requests

Post by civic1234 » Thu Jun 30, 2016 10:46 pm

I have a few request my self:

1. Anti-theft or Key ON security check just like S300, I normally program the S300 to see full throttle before you can start the car. This saves me from installing a kill switch for thieves.

2.Air temperature compensation for Boost control just like S300, I usually boost 1-2 PSI lower in Hot summer weather and would like to see same boost level year round.

sass
Posts: 104
Joined: Mon Oct 06, 2008 5:07 am
Location: Evropa-Estonia-Tallinn

Re: KPro / KManager requests

Post by sass » Tue Jul 26, 2016 1:00 am

Hondata wrote:Max vehicle speed would be easier, but would just maximum gear be better still?
How are you?


is all that I can
Image
Cr-v RD8+K24A2turbo+Kpro V4 prb+NPR3/6Speed+ТС+ HFS4 v3.2.
DynoWheel = 472kW / 589 N.m
HRX One Mile Challenge = Max Speed 282km
Known as Sniper

Honda
Posts: 28
Joined: Sat May 17, 2014 9:59 am

Re: KPro / KManager requests

Post by Honda » Sat Jul 30, 2016 3:19 pm

nitrous arming inputs by kpro v4 analog inputs.
AC switch input by analog inputs.

D-Rob
Posts: 61
Joined: Tue Apr 29, 2008 6:11 am

Re: KPro / KManager requests

Post by D-Rob » Mon Aug 01, 2016 2:30 pm

Closed loop target boost control, or at the very least, IAT compensation for boost control.

Please, pretty please?

sass
Posts: 104
Joined: Mon Oct 06, 2008 5:07 am
Location: Evropa-Estonia-Tallinn

Re: KPro / KManager requests

Post by sass » Mon Aug 01, 2016 10:18 pm

D-Rob wrote: IAT compensation for boost control.

Please, pretty please?
+10000000000000000
Cr-v RD8+K24A2turbo+Kpro V4 prb+NPR3/6Speed+ТС+ HFS4 v3.2.
DynoWheel = 472kW / 589 N.m
HRX One Mile Challenge = Max Speed 282km
Known as Sniper

sass
Posts: 104
Joined: Mon Oct 06, 2008 5:07 am
Location: Evropa-Estonia-Tallinn

Re: KPro / KManager requests

Post by sass » Thu Sep 08, 2016 10:59 pm

sass wrote:
Hondata wrote:Max vehicle speed would be easier, but would just maximum gear be better still?
How are you?


is all that I can
Image
This scheme does not work
When you turn off the ECM receives a signal 4.25 volts

Image

Misfier
Cr-v RD8+K24A2turbo+Kpro V4 prb+NPR3/6Speed+ТС+ HFS4 v3.2.
DynoWheel = 472kW / 589 N.m
HRX One Mile Challenge = Max Speed 282km
Known as Sniper

RAIN H8R
Posts: 28
Joined: Wed Sep 14, 2011 3:00 pm
Location: Wales, WI

Re: KPro / KManager requests

Post by RAIN H8R » Sat Oct 29, 2016 3:54 pm

afzan wrote:s2000 - would like the ability to adjust the coolant temperate gauge scaling

similar to this:
Image
This would be extremely helpful. Please be sure to make it editable for both AP1 and AP2 Clusters, but especially the AP1 with it only have 6 bars.

More information, and reasons why it is needed can be found here. http://www.modifry.com/index.php?route= ... uct_id=157

Post Reply